Engineers in Australia work to tight rules. Concrete structures are designed to AS 3600, bridges to AS 5100, and the prestressing steel has to meet AS/NZS 4672. When you buy prestressed concrete strand Australia specifications can accept, the paperwork matters as much as the steel, so we ship the test records with every coil.
Wasungen focuses on prestressed concrete materials, and our strand is used in bridges, railway sleepers, highway slope protection, water conservancy works and high-rise buildings. For Australian projects we supply 7 wire prestressing strands for precast yards, post tensioned slabs, bridge girders and ground anchors. Each coil is traceable by heat number, and each order comes with test certificates your quality manager can check against the purchase order.
Australia is hard on steel. Coastal towers in Queensland and New South Wales sit in salt air for decades. Mining and energy sites in Western Australia are remote and costly to repair. Tunnels and bridges on the east coast are designed to last a century. That is why we make PC strands, and why we help buyers match the strand to the site instead of simply selling the cheapest coil.
Plain PC Strand
As a prestressed steel strand supplier, we get asked for the same sizes again and again. These are the sizes we supply, all 7 wire, low relaxation and 1860 MPa (Grade 270), produced to AS/NZS 4672, ASTM A416, EN 10138, KS D7002 and GB/T 5224.
| Diameter | Tensile grade | Steel area | Min. breaking load | Types available | Typical use |
|---|---|---|---|---|---|
| 12.7 mm | 1870 MPa (Grade 270) | 98.6 mm² | 184 kN | PlainEpoxy coatedUnbonded | Precast beams, planks, slabs, post tensioned floors |
| 15.2 mm | 1860 MPa (Grade 270) | 140 mm² | 261 kN | PlainEpoxy coatedUnbonded | Bridge girders, post tensioned bridges, heavy precast |
| 15.7 mm | 1860 MPa (Grade 270) | 150 mm² | 279 kN | PlainEpoxy coatedUnbonded | Larger tendons, high capacity anchorage systems |
A few points that save time at the approval stage and on site:
Need a size, grade or coating that is not in the table? Ask us. We can quote high tensile PC strands to project-specific requirements.
In Australia, prestressing steel is covered by AS/NZS 4672.1 (general requirements, including the strand section) and AS/NZS 4672.2 (testing requirements). They replaced the older AS 1311 and AS 1313. The standard sets out how strand is built, its tensile strength, its relaxation limits and how it is tested.
Many projects also ask for third-party certification. The usual route is ACRS, the Australasian Certification Authority for Reinforcing and Structural Steels, which certifies prestressing wire and strand to AS/NZS 4672. Some state road authorities keep their own approved lists too. Queensland Transport and Main Roads, for example, publishes a registered prestressing strand list for bridges and other structures.
Our PC strand meets AS/NZS 4672 or ACRS certification, tell us before you order. We will confirm what testing and certification we can provide for your grade and size.
As a PC strand manufacturer Australian buyers can audit, we send these documents with every shipment:
Prestressing strand is used in Australian building, bridge, precast concrete and ground-engineering projects. Product selection depends on the approved design, applicable specification and installation system.
Strand is used in post-tensioned slabs and beams. In bonded systems, the strands are installed in ducts, stressed after the concrete reaches the specified strength, and then grouted.
Strand is used in prestressed bridge components, post-tensioned structures and selected strengthening applications.
Strand is used in factory-produced elements such as beams and hollow-core slabs. The required strand properties and coil dimensions should match the design and production equipment.
Strand can form part of engineered anchor systems for soil, rock and underground support. These applications require project-specific assessment of mechanical properties, corrosion protection and anchorage compatibility.
Send us your application and technical specification so we can confirm whether our available strand meets your requirements.
Yes. We are a PC strand supplier Australia contractors, importers, distributors, precasters and procurement teams can order in bulk, from a single container to regular repeat shipments. Send us the strand size, grade, quantity and delivery port, and we will quote against them.
We supply plain, unbonded, epoxy coated 7 wire prestressing strands. Sizes include 12.7 mm, 15.2 mm and 15.7 mm, all low relaxation, produced to AS/NZS4672, ASTM A416, EN 10138 and GB/T 5224 and shipped with mill test certificates.
Yes. We can set up scheduled shipments, consistent packing and standing documentation, so your stock of prestressed concrete strand arrives on a predictable timeline. Many distributors start with a trial container and move to regular orders.
Yes. Our 15.2 mm strand is widely used in bridge girders and post tensioned decks, and our 12.7 mm strand in precast beams, planks, piles and sleepers. Every shipment includes test records so your quality team can check the strand against the specification.
Yes, and you should. Plain low relaxation strand suits most precast and bonded post tensioning work. Unbonded strand suits post tensioned slabs, and coated strand suits corrosive sites. Tell us the application and we will recommend a type, but the final choice must match your designer's specification.
Yes. Our export team handles quotations, specification checks, production updates and shipping documents in English. That includes mill test certificates, packing list, bill of lading and certificate of origin. Our time zone is close to Australia's, so replies fit your business day.
Yes. Send the strand size, grade, coating, quantity and delivery port, along with any specification clause or drawing note, and our team will reply with pricing, specifications, packing and lead time for your high tensile PC strand order.
